Tray Cover Is Closed Please Open the Cover and Try Again

If an fault message is displayed on the LCD, take the corresponding action described beneath.

The ink may have run out. Replacing the ink tank is recommended U041

If the lamp on the ink tank is flashing, ink may have run out.

Replacing the ink tank is recommended.

If printing is in progress and you want to continue printing, touch the machine's OK button with the ink tank installed. Then printing can go along. Replacing the ink tank is recommended later the printing. The machine may be damaged if printing is continued under the ink out condition.

REFERENCE

• If multiple ink lamps are flashing carmine, refer to [ Checking the Ink Condition ] and check the condition of each ink tank.

Some ink tanks are non installed in place U072/More than one ink tank of the post-obit color is installed U071

• Some ink tanks are not installed in the correct position. (The lamp on the ink tank flashes.)
• More than one ink tanks of the same color are installed. (The lamp on the ink tank flashes.)

Confirm that the ink tanks are installed in the appropriate positions.

Replacing an Ink Tank

When you need to supervene upon an ink tank, follow the procedure below.

See[Replacing an Ink Tank ]

The remaining level of the ink cannot be correctly detected. Replace the ink tank. U130

The remaining ink level cannot exist correctly detected. (The lamp on the ink tank flashes.)

Replace the ink tank and close the scanning unit of measurement / embrace.

Printing with an ink tank that was once empty may damage the machine.

If you lot want to keep press in this condition, yous need to release the function for detecting the remaining ink level. Touch the automobile's End button for at least 5 seconds, and then release it.

With this functioning, releasing the function for detecting the remaining ink level is memorized. Delight exist brash that Canon shall non be liable for any machine malfunction or impairment caused past refilled ink tanks.

REFERENCE

• If the office for detecting the remaining ink level is disabled, the ink tank in greyness is displayed on the LCD when checking the current ink level.

The post-obit ink tank cannot be recognized U043 U140 U150

• The ink tank is not installed. Install the ink tank.

• Advisable ink tank is not installed.

Printing cannot be executed because the ink tank is non compatible with this machine.

Install the appropriate ink tank.

If yous want to abolish printing, touch the car'south Stop push.

• The ink tank cannot be recognized. (The lamp on the ink tank is off.)

Replace the ink tank.

Appropriate ink tank is non installed. Install the appropriate ink tank U141

Advisable ink tank is not installed.

Printing cannot be executed considering the ink tank is not compatible with this motorcar.

Install the appropriate ink tank.

If you want to cancel printing, touch on the machine'due south Stop button.

The ink has run out. Replace the ink tank U163

The ink has run out. (The lamp on the ink tank flashes.)

Replace the ink tank and close the scanning unit of measurement / comprehend.

Press under the current condition may impairment the machine.

If you lot want to continue printing in this condition, you need to release the role for detecting the remaining ink level. Touch the machine'southward Stop button for at least 5 seconds, and then release it.

With this operation, releasing the function for detecting the remaining ink level is memorized. Please be advised that Canon shall not exist liable for any malfunction or trouble which may be caused by continuation of printing under the ink out condition.

REFERENCE

• If the function for detecting the remaining ink level is disabled, the ink tank in greyness is displayed on the LCD when checking the current ink level.

Data of supported types are not saved

• There is no image information or document saved on the retentiveness carte du jour or USB flash drive that can exist read by this machine.
• The machine may not recognize the file if the file name or binder path contain certain characters. Apply but alphanumeric characters.
• Photo data edited or processed on a estimator must be printed from the figurer.

REFERENCE

• When a photo which has been processed on a estimator is selected, "?" is displayed on the LCD.

Cannot print the specified PDF file. An mistake has occurred while scanning the file, or the format is not supported, or the file is too large

• Make sure the PDF file is printable from a retention card or USB wink drive.

REFERENCE

• The names of the PDF files are displayed even though they cannot be printed from the memory card or USB flash drive. It is recommended you confirm whether they are printable. If one of the post-obit weather applies to the PDF files, they are not printable.

- The Details screen is not displayed for the PDF file you desire to print.

- Characters other than automobile proper noun, MP Navigator EX V5.0, or MP Navigator EX are displayed on Created with on the Details screen.

- "?" is displayed on the preview screen.

• Data edited or candy on a calculator must be printed from the reckoner.

The specified PDF file contains unprintable information. Some portions may not be printed. Some portions may non exist printed

PDF file which contain lot of graphics or how-do-you-do-resolution images may lose that information or stop before printing is completed. In this case, impress from the computer.

Inner cover is open. Shut the cover and select OK

If the inner comprehend (the cover of the disc tray) is open while printing other than disc label printing is in progress, close the inner cover, then touch on the OK push.

Open the inner cover, set up the disc tray and select [OK]

If the inner encompass is closed when starting disc characterization press, open up the inner cover with the scanning unit / cover airtight, set the disc tray, and then touch the OK push on the machine to dismiss the error.

Practice not open up or shut the inner encompass while printing is in progress. Doing then may damage the machine.

Cannot prepare to print. Inner cover is open. Shut the inner cover and select [OK]

If the inner cover is open when starting disc characterization printing, close the inner cover with the scanning unit / cover closed, set the disc tray, and and then affect the OK button on the motorcar to dismiss the error.

The ink cushion is almost full. Printing OK to continue printing. Contact the service center

The ink absorber is almost total.

Touch the machine's OK push to continue press. Contact the service heart.

Printer error has occurred. Contact the service centre

The machine mistake has occurred.

Contact the service eye.

Timeout error has occurred

Some errors occurred while copying and a certain fourth dimension passed.

Affect the OK push to dismiss the error, and attempt to re-create again.

Incompatible device detected. Remove the device

• Cheque the device continued to the Direct Print Port. Printing photos directly is possible with a PictBridge compliant device or the optional Bluetooth Unit BU-xxx, or a USB flash drive.
• A advice time out occurs if an performance takes likewise long or if it takes as well much time to send data. This may cancel printing. In such cases, disconnect and reconnect the USB cable. When printing from a PictBridge compliant device, depending on the model or brand of your device, you may have to select a PictBridge compliant impress mode on the device before connecting it to the machine. You may too have to turn on your device or select Play manner manually after connecting the device to the machine. Perform necessary operations earlier connecting your device referring to its pedagogy manual. If the error is notwithstanding non resolved, bank check if you tin impress another photograph.

Automobile caput align has failed. Select OK and repeat functioning. <Run across manual>

• Print head nozzles are clogged.

Bear upon the OK push button to dismiss the error, and print the nozzle cheque pattern to check the status of the print head.

• Paper of size other than A4 or Letter is loaded in the rear tray.

Touch the OK push button on the machine to dismiss the mistake, and then load a sail of A4/Letter of the alphabet-sized Canon Matte Photo Paper MP-101 with the press side (whiter side) facing UP in the rear tray.

For Automated Impress Head Alignment, always load paper in the rear tray.

• The paper output slot is exposed to potent light.

Touch the OK push to dismiss the error bulletin, so adjust your operating environment and/or the position of the car and then that the paper output slot is not exposed directly to potent light.

Subsequently carrying out the above measures, if the problem continues after aligning the print caput once more, touch the OK button to dismiss the error, and then perform Manual Impress Head Alignment.

An unsupported USB hub is continued. Remove the hub

If a PictBridge compliant device is continued via a USB hub, remove the hub and connect information technology directly to the machine.

B200 Printer error has occurred. Unplug the power cord and contact the service center

Turn off the motorcar, and unplug the power cord of the machine from the ability supply.

Contact the service center.

**** Printer error has occurred. Turn off ability then back on again. If problem persists, see the manual

"****" is displayed in the alphanumeric character and depends on the error occurred.

• 5100 is displayed:

Cancel press, and plow off the auto. So clear the jammed paper or protective material that is preventing the impress head holder from moving, and plow on the auto again.

Of import

• Be careful not to bear on the components within the car. The machine may not print out properly if you touch it.
• If the problem is not resolved, contact the service eye.

• 6000 is displayed:

If whatsoever object is placed in forepart of the automobile, remove it.

Open up the Paper Output Tray gently, and then turn the power off and back on.

• In other cases:

Plow off the machine, and unplug the power cord of the car from the power supply.

Plug the machine back in and turn the machine back on.

If the trouble is non resolved, contact the service eye.

5101 Remove the protective fabric if it is fastened to the holder and turn off power and back on

Check the inside of the machine. If you lot observe the protective fabric attached to the holder, remove it, turn the motorcar off, then turn information technology back on.

Turn the machine off, then check the inside of the auto. If the protective fabric remains attached, remove it and turn the machine dorsum on.

If the problem is not resolved, contact the service centre.

Scanner is non operating correctly

Turn off the machine, and unplug the power cord of the machine from the ability supply.

Subsequently a while, plug the ability cord of the automobile back in, so turn on the machine. If the aforementioned error occurs, contact the service center.

Release the scanner lock switch and turn off ability and so back on again

The Scanner Lock Switch is not released. Slide the Scanner Lock Switch to the release position ( ) and press the ON push to plow the machine off.

And then, plow the power back on. If this error still remains, contact the service heart.

The carte is currently writable from PC. Set to [Not writable from PC]

The Carte du jour Slot is set to Writable from USB PC or Writable from LAN PC.

You cannot print from the retention carte or salvage the scanned data to the retentivity card when the Card Slot is set to Writable from USB PC or Writable from LAN PC. Later writing on the retention card, select Not writable from PC in Read/write attribute in Device user settings.

Power was non turned off correctly the last time. Press the ON button when turning power off

The ability cord may take been unplugged terminal while the car was even so on.

Touch the OK button to dismiss the error.

Cannot impress the data

When you print the contents on CREATIVE PARK PREMIUM, ostend the message on the reckoner screen, make sure that genuine Canon ink tanks are installed properly for all colors, then commencement printing again.

Cannot connect to the server. Please await a while and try over again

Y'all cannot connect to the server due to some communication error. When you have tried to access a photograph sharing site, it is possible that your photos have been deleted.

Touch the OK button to dismiss the error, and so try again after a while.

reidtheract.blogspot.com

Source: https://id.canon/id/support/8201208400